Vacpan Automatic Dustpan
The VacPan is a must have for any
existing or new central vacuum
 The Original VACPAN
adds a new dimension of convenience to your central vacuum by giving your broom the power of a central vac. Simply brush dirt and debris toward the powerful suction
plate and your floor is clean - instantly! Also
available is the VacPan II which is a dual function
central vacuum inlet valve system. This VacPan
model offers the added convenience of a standard hose
wall inlet in one compact design. Each VacPan
model provides unique benefits, allowing you to pick the
right model for every room. VacPan &
VacPan II may be added to existing or new installations.
Original VacPan Inlet Valve
Automatic Dustpan - Perfect for Any Central Vacuum
-
Sweep Inlet Valve
-
Flush Mount
-
Available in White, Black, and Ivory
-
Stainless Steel Faceplate Sold Separately
-
Top Loading Hose Design
-
Installs Out-of-Sight under toe-kick
-
Uses: Bathroom, Kitchen, Hallways, Mudrooms, Laundry Rooms, and any
other room where you don't want to lug
around that bulky central vacuum hose!
|
|
VacPan
- Get Swept Away (An Automatic Dustpan
for Your Central Vacuum System)
The VacPan automatic dustpan is the perfect companion for any central vacuum system. Flush mountable to your wall or cabinet kickboard, the VacPan is the convenient way to clean up dirt and debris when using a broom. Don't
Forget to Order VacPan QuickTrim Plates
Using the VacPan is easy. Simply turn the convenient foot switch to the on position and sweep dirt and debris toward the VacPan. The powerful suction from your central vacuum system does the rest.
The VacPan is a perfect fit for any room where you sweep - kitchens, workshops and garages. Installation is easy using standard fittings and pipe and can be installed in new and existing homes features a central vacuum system.
|
|
Customers
Who Bought a VacPan Also Purchased
The Following Items: |
Flexi Hose VacPan Adaptor Kit
-
Flexible - up & over tight areas inside your cabinets
-
Flexi Hose Kit Includes: 1
VacPan, 1 Flexi Hose, 2 Hose Clamps, 1 Sweeping Tee, 1 Short Tee Fitting, Special Couplers, and Low Voltage Wire
-
Easy to Install!
|
|
|
 QuickTrim
for
(VacPan)
-
Enhances
your VacPan to match decor
-
Great for
retro-fit installations
-
Hides Installation
Screws
-
VacPan NOT Included
|
|
|
VacPan Brushed Stainless Steel
Face Plate
QuickTrim plate will
enhance your VacPan to
match your decor.
Allows installation
using a cut out up to
10.5" X 4"
in size.
Great for retro-fit installations.
Very durable & hides
installation screws.
Easy To Install
For VacPans Only |
|
|
(VacPan)
Repair Kit
Comes in Black, White, Ivory
SIMPLE / EASY
TO REPAIR
Click for
Quick Repair Instructions |
|
|
Other Options Similar to The VacPan
Automatic Dustpan |
|
VacPan II Dual Function Inlet Valve
System
Automatic Dustpan - Perfect
Companion for Any Central Vacuum
-
Dual function-sweep inlet/hose inlet
-
Mounts in wall at floor level
-
No need for a bulky central vacuum hose
-
Automatic Dustpan - No hands & knees
-
Uses: Bathroom, Kitchen, Hallways, Mudrooms,
Laundry Room, etc.
|
|
|
VacuSweep Automatic Dustpan
Automatic Dustpan - Great
Companion for Any Central Vac
|
|
VacPan Installation Instructions
Using the VacPan is easy. Simply turn the convenient foot switch to the on position and sweep dirt and debris toward the VacPan. The powerful suction from your central vacuum system does the rest.
The VacPan is a perfect fit for any room where you sweep - kitchens, workshops and garages. Installation is easy using standard fittings and pipe and can be installed in new and existing homes features a central vacuum system.
VacPan Installation Tips
Plan the location of your Original
VacPan to be conveniently located for sweeping clean-ups. Also consider
ease of access of vacuum tube piping connections during installation. The leading edge of the Original
VacPan must sit flush with the finished floor. For maximum clearance, use Plastiflex
part #SV8052 Universal Short 90 degree Elbow for connections to VacPan. Do not glue the connection between
Original VacPan and elbow, to allow for future removal. Prior to final installation, check for an airtight seal between Original VacPan and elbow. Teflon tape may be
used if required. Allow for 1/2" vertical play in vacuum
tube piping a Original VacPan location, so that final piping connections
can be made.
In Wall Installations
-
 Original VacPan can be
installed between wall studs inside walls.
Original VacPan should be
located tight to one side in stud space. Once the Original VacPan
location is determined, cut a 6-3/4" long x 1-3/4" high slot
in the wall and baseboard to accept the Original VacPan. The 2 x 4 wall bottom plate
between the two studs must be removed. This can be achieved
from below using a hole saw. In new home construction,
the bottom wall plate can be removed directly. A 6-3/4" length
of 2 x 4 can be used as a temporary rough in block, that will
force all trades to finish around, leaving a slot for the
Original VacPan Floor contractor must run flooring under
block. Run vacuum tube piping and
low voltage wire from the main line to Original VacPan
location. Access for final piping
connections must be made.
Inlet Types and Installation Diagrams
Access From
Below
If access is available from below, cut an access hole
through the subfloor underneath the wall between the studs,
positioned so that final piping connections can be made by
reaching through the access hole.
Access Through Wall
Access can be made through the finished wall. Cut a 2-3/4" x
3-1/2" access hole, positioned so that final piping
connections can be made by reaching through the access hole.
Plastiflex part #SV8012 Cover Plate can be used to cover the
hole afternstallation.
Attach low voltage wires
to Original VacPan terminal connections marked "low
voltage only" Slide Original VacPan
into mounting slot and secure to toe kick using two #6
screws provided. Reach through access
hole and make final piping connections |
Click Image For
Full View |
 Under Cabinet
Installations
-
Original VacPan requires a minimum
2-1/4" toe kick height.
-
Once the Original VacPan location
is determined, cut a 6-3/4" long x 1-3/4" high slot in the
cabinet toe kick to accept the Original VacPan.
-
Run vacuum tube piping and low
voltage wire from he main piping line to the Original VacPan
location.
-
Access for final piping
connections must be made.
|
Access From Below
If access is available from below, cut an access hole
through the subfloor underneath the cabinet, positioned so that
final piping connections can be made by reaching through the
access hole.
Access Through Cabinet Floor
Access can be made through the finished cabinet floor.
Cut a 2-3/4" x 3-1/2" access hole, positioned so that final
piping connections can be made by reaching through the access
hole. Plastiflex part #SV8012 Cover Plate can be used to cover
the hole after installation.
Access Through Cabinet Toe Kick
Access can be made through the cabinet toe kick by
cutting up to a 10-1/2" x 4" slot and using the Original VacPan
Quick Trim Cover Plate (included or Plastiflex part #VCPx01 sold
separately). If required, score back of Quick Trim Cover Plate
with a knife and snap along grooves for height adjustment.
Attach low voltage wires
to Original VacPan terminal connections marked "low
voltage only" Slide Original VacPan
into mounting slot and secure to toe kick using two #6
screws provided. Reach through access
hole and make final piping connections
|
Click Image
For Full View |
|
|
|
|
Aggresor
